How To Set Up A Scansnap Ix500

Set up the ScanSnap that you purchased for the start time so that it is gear up to scan with ScanSnap Habitation.

The following preparations are required before you set up up the ScanSnap.

ATTENTION

• Do not connect the ScanSnap to the computer earlier installing the software.

• Check that all items are included in the package

  For details, refer to Package List.

  For details, refer to "Package List" in Getting Started that is supplied with the scanner.

  HINT

  • When Getting Started is included in the package, refer to "Packet List" in Getting Started.

• Remove the protective inner encompass and tape () and the cardboard canvass () from the ScanSnap

  

• Remove the protective inner embrace and tape () and the paper-thin sheet () from the ScanSnap

  

• Remove the materials used for protection from the ScanSnap

  For details, refer to Getting Started that is supplied with the scanner.

• Remove the protective inner cover and tape () and the cardboard sheet () from the ScanSnap

  

  • The information on the bill of fare may exist lost if the black magnetic part of a magnetic card or IC bill of fare is in contact with the magnetic part ().

• Remove the tape seal () and tape () from the ScanSnap

  

• Remove the record () and tape seal () from the ScanSnap

  

• Remove the tape seal () from the ScanSnap

  

• Remove the tape seal () and record () from the ScanSnap

  

• Connect the ScanSnap and the computer with a USB cable, and charge the battery until the battery indicator lite turns off

  

  Attending

  • Do non open the feed guide until the instructions are displayed on the window for installing software.

  • The ScanSnap can exist charged with the supplied USB cable or optional USB power adapter. For purchasing details of the USB power adapter, refer to "Suppliers of Consumables/Optional Parts" in Customer Support.

• Attach the extenders to the ScanSnap

  Attention

  • The following preparations are required earlier you attach the extenders.

    • Wipe off dust and clay such as oily dirt on the place where the extenders volition be attached

    • Pare the protective tape off the bottom of the extenders

  Leaving near 3 to five mm of space between the extenders and the back and side of the ScanSnap, push the extenders down until they lock in place. If the extenders are placed against the side of the ScanSnap base or the protrusion of the extenders are placed on the ScanSnap base, the lesser of the extenders may not stay in place firmly.

  

The process to set the ScanSnap is as follows:

1. Configuring the Settings of the ScanSnap

2. Downloading the Software

3. Installing the Software/Connecting the ScanSnap

Configuring the settings of the ScanSnap

1. Connect the power cablevision to the power connector on the ScanSnap and the AC outlet.

   

   • Utilise merely the AC adapter and cables that are bundled with the ScanSnap. Using other adapters and cables may cause a scanner failure.

2. Open the ADF newspaper chute (cover) to turn the ability on.

   

3. Configure the settings of the ScanSnap by following the instructions on the touch on panel.

   

   

   Ready the display language for the bear on panel, the startup manner, and a device that is used with the ScanSnap.

   To set up the scanner past using a mobile device, follow the instructions displayed on the touch panel to connect the ScanSnap to a wireless access point.

When the [USB Connection] window is displayed on the touch on panel, the setting procedure for the ScanSnap is consummate.

If you gear up upwardly the scanner by using a mobile device, when [Launch the software on the device and connect it to the ScanSnap.] is displayed on the touch console, the setting procedure for the ScanSnap is complete.

Downloading the Software

On your computer or mobile device, download the software from hither.

On your calculator, download the software from here.

To set up the ScanSnap by using a mobile device, refer to Using the ScanSnap with a Mobile Device.

• When your estimator is connected to the Cyberspace

  Click [Download Installer] to download the software.

• When your computer is not continued to the Internet

  On another figurer that is connected to the Internet, click [Offline Installer] to download the software in advance.

  Copy the downloaded software to your computer.

To ready the ScanSnap by using a mobile device, refer to Using the ScanSnap with a Mobile Device.

Installing the Software/Connecting the ScanSnap

1. Run the installer that you saved on your computer.

2. When the [ScanSnap Home Setup] window (Welcome to ScanSnap Habitation Setup) appears, click the [Next] button to outset installing the software.

   Follow the instructions to install the software.

   

3. The window for selecting a model to be continued appears afterward the installation is complete, select a ScanSnap model that you desire to connect so click the [First setup] button.

   

4. When the [ScanSnap Home - Connecting ScanSnap] window (Connect the ScanSnap to your computer) is displayed, follow the instructions on the window to connect the ScanSnap to a calculator via a USB cable and click the [Next] button.

   • Do not utilize a cablevision other than the supplied i to connect to the ScanSnap. Using other cables may cause a scanner failure.

   HINT

   • If you cannot connect a USB cable to a computer, click [If you cannot connect the USB cable to the computer, refer to this link] displayed in the lower left of the [ScanSnap Home - Connecting ScanSnap] window (Connect the ScanSnap to your computer), and follow the instructions on the window to connect the ScanSnap to the reckoner via Wi-Fi.

     The default scanner name of the ScanSnap is "ModelName-<Serial No.>".

     To connect the ScanSnap and a computer via Wi-Fi, you need to connect the computer and the ScanSnap to the same wireless admission point.

   HINT

   • If you cannot connect a USB cable to a reckoner, click [Setup without the USB cablevision] displayed in the lower left of the [ScanSnap Domicile - Connecting ScanSnap] window (Connect the ScanSnap to your figurer), and follow the instructions on the window to connect the ScanSnap to the figurer via Wi-Fi.

5. When the [ScanSnap Home - Connecting ScanSnap] window (How to connect ScanSnap) is displayed, follow the instructions on the window to connect the ScanSnap to a calculator via a USB cable and click the [Next] push button.

   • Practice not employ a cablevision other than the supplied 1 to connect to the ScanSnap. Using other cables may crusade a scanner failure.

6. Follow the instructions on the window and open up the ADF paper chute (cover) of the ScanSnap to turn the power on, then click the [Next] button.

   

   

   

7. Follow the instructions on the window and concord the right side of the ADF paper chute (embrace) of the ScanSnap, and open information technology to turn the power on, then click the [Next] button.

   Open the ADF paper chute (embrace) fully then that the [Scan] push button lights up in blue.

   When the ADF paper chute (encompass) is opened, the extension volition ascent automatically.

   

8. Follow the instructions on the window and open the ADF paper chute (embrace) of the ScanSnap to turn the power on, then click the [Side by side] button.

   

   

9. Follow the instructions on the window and press the [Scan] button or [Stop] button on the ScanSnap to turn the power on, and so click the [Next] button.

   

10. When the [ScanSnap Habitation - Connecting ScanSnap] window (Select a startup manner.) appears, select a startup style and click the [Next] button.

11. When the "Connection is complete" window appears, click the [Next] push.

    

12. When the "ScanSnap has been connected successfully." window appears, click the [Finish] button.

    

13. The window for checking whether to configure the Wi-Fi settings for the ScanSnap is displayed.

    Wi-Fi connection

    Attention

    • To connect the ScanSnap and a figurer via Wi-Fi, the reckoner must be already connected to the wireless access signal that you desire to connect the ScanSnap to.

    Click the [Yes] button.

    When the wireless network setup sorcerer appears, follow the instructions on the window to connect the ScanSnap to a wireless access point.

    USB cable connection

    Click the [No] button.

    The Wi-Fi settings for the ScanSnap can exist configured later.

    For details, refer to Connecting the ScanSnap and the Estimator Via a Specified Wireless Access Point.

    For details, refer to Configuring the Wi-Fi Settings.

14. When the [ScanSnap wireless network setup] window appears, select whether to configure the Wi-Fi settings for the ScanSnap.

    Wi-Fi connection

    ATTENTION

    • To connect the ScanSnap and a reckoner via Wi-Fi, the estimator must be already connected to the wireless admission point that you desire to connect the ScanSnap to.

    Click the [Setup now] button.

    When the wireless network setup magician appears, follow the instructions on the window to connect the ScanSnap to a wireless access point.

    USB cablevision connection

    Click the [Later] button.

    The Wi-Fi settings for the ScanSnap tin can be configured later.

    For details, refer to Configuring the Wi-Fi Settings.

15. When the video tutorial is displayed, view the video explaining the basic utilise of ScanSnap Home, if necessary.

    HINT

    Windows

    The video tutorial tin exist viewed afterwards at anytime.

    To view the video tutorial, select [Help] → [View the video explaining the method of use] in the menu.

    Mac Bone

    The video tutorial can be viewed afterwards at anytime.

    To view the video tutorial, select [Help] → [View the video explaining the method of use] on the card bar.

16. When the [ScanSnap Home - Connecting ScanSnap] window (Let's utilize it!) appears, check the contents and click the [Shut] push button.

    When the tutorial which explains the bones utilize of ScanSnap Dwelling appears, click the [Start] push to brainstorm the tutorial, if necessary.

    HINT

    Windows

    The tutorial tin exist viewed later at anytime.

    To view the tutorial, select [Help] → [Tutorial] in the bill of fare.

    Mac OS

    The tutorial can be viewed after at anytime.

    To view the tutorial, select [Help] → [Tutorial] on the carte du jour bar.

When the ScanSnap is continued correctly, the scanner proper name of the connected ScanSnap is displayed in [Select a scanner] in the Scan Window.

The scan window appears when you click the [Scan] button at the pinnacle of the Primary Window of ScanSnap Home.

The window varies depending on the ScanSnap to be connected.

ScanSnap Domicile allows y'all to register your favorite scan settings for the ScanSnap equally a profile ().

Multiple user-friendly profiles are available by default. For details, refer to What is a Profile?.

Profiles are displayed both on the touch panel of the ScanSnap and in the scan window of ScanSnap Abode.

On the touch panel of the ScanSnap or in the browse window of ScanSnap Habitation, select a contour, and press the [Scan] button to perform a scan.

In the scan window, select a profile, and click the [Scan] button to perform a scan.

Source: https://www.pfu.fujitsu.com/imaging/downloads/manual/ss_webhelp/en/help/webhelp/topic/su_intro_first.html

Share this post